Tuesday, July 5, 2022

author photo

HEMTT M1120A2.jpg

The M1120 HEMTT LHS (Load Handling System) is a M977 Heavy Expanded Mobility Tactical Truck with a load handling system in place of a flat bed. The HEMTT is an eight-wheel drive, diesel-powered, tactical truck used by the US military and others. The HEMTT is manufactured by Oshkosh Defense and entered Army service in 1982, with the M1120 variant first produced in 1999.

Following the evaluation of proposals submitted by AM General, MAN, Pacific Car and Foundry (PACCAR) and Oshkosh Truck Corporation, In May 1981, the then U.S. Army Tank Automotive Command awarded an initial five-year contract valued at US$251.13 million to Oshkosh Truck Corporation for production of the 10 ton (9,070 kg) 8 x 8 Heavy Expanded Mobility Tactical Truck (HEMTT).

The M1120 LHS variant was initially introduced as part of the HEMTT overhaul/rebuild programme, during which returned M977 Cargo variants have their cargo bodies and materials handling cranes removed, to be replaced by a Multilift Mark 5 (now designated MPH165-LHS) load handling system, as fitted to the Oshkosh PLS truck. Other modifications include an upgrade of the rear suspension.


The first rebuilt M1120 was produced in late-1999, with new build M1120A2 examples (now A4) available from February 2004.

By mid 2019 Oshkosh had manufactured (new build) 35,000 HEMTTs of all types. Specific figures for the M1120 LHS variant are not available.

For reference, original HEMTT models now have the suffix A0. Only the M984 wrecker was produced in A1 configuration. All models were produced in A2 configuration. The A3 suffix is applied to HEMTT technology demonstrators with a diesel-electric drive system. All current HEMTT production models have the suffix A4.

The HEMTT was developed from the outset as a tactical truck, but to minimize procurement and life cycle costs included militarized commercial automotive components where possible, these including the engine and transmission. Some components used in early HEMTTs are common with the Oshkosh Logistics Vehicle System (LVS) vehicles which were supplied to the U.S. Marine Corps.

The chassis of the M1120 is formed of 257 × 89 × 9.5 mm heat-treated carbon manganese steel with a yield strength of 758 MPa. With the exception of the wrecker variant, this chassis is common on all HEMTT variants Bolted construction with Grade 8 bolts is used throughout. A centrally mounted self-recovery winch is an option and this is fitted to around 20% of production.

The two-door forward control cab seats two. It is of heavy-duty welded steel construction with corrosion-resistant sheet metal skins. Add-on armor kits were produced by Simula Inc. and BAE Systems. The current HEMTT A4 is fitted with the slightly larger from the Oshkosh PLS A1. This cab complies with the U.S. Armys Long Term Armor Strategy (LTAS) requirements of an A- and B-kit armoring philosophy. It also comes as standard with integrated floor armor, an integrated mount for a machine gun and gunner protection kit, and air-conditioning.

A Detroit Diesel 8V92TA V-8 two-stroke DDECIV diesel developing 445 hp is fitted to A2 HEMTTs. An EPA 2004 compliant Caterpillar (CAT) C-15 six-cylinder, 15.2-liter diesel developing a peak of 515 hp is fitted to HEMTT A4 models. HEMTT A2 models have an Allison HD 4560P 6F/1R automatic transmission coupled to an Oshkosh 5500 series 2-speed transfer case, while A4 varinats are fitted with an Allison 4500SP 5F/1R automatic transmission and an uprated version of the 55,000 series two-speed transfer case.

The front axles on all HEMTTs are single-reduction Oshkosh 46K, the rear are Dana DS480 single-reduction. Drive to the front axles is selectable and all axles have differential locks. Suspension on the A2 variant is by Hendrickson RT40 leaf springs with equalizing beams. Suspension on A4 models is Holland air suspension, ADS-240 (front) and AD-246 (rear). Tire size is 1600 R20 on all models, and standard tire fit is Michelin XZL.

All M1120 variants are capable of fording water crossings up to 48 inches deep, and can climb a gradient of at least 60%. All M1120 variants are air transportable in the C-130 and C-17 transport aircraft.

The M1120 HEMTT LHS is fitted with Multilift Mark 5 (now designated MPH165-PLS) load handling system, this an imperial variant of the Mark 4/MPH165 that is further-modified to include a folding hook arm to bring the system within C-130 Hercules air-transport height constraints. The MPH165-PLS system is produced under licence by Oshkosh and is also fitted to the M1074 and M1075 PLS and Logistic Vehicle System Replacement (LVSR). The MKVI LHS (now designated MPH165-CBT) is a further development of the MPH165-PLS and has additional fixings and hydraulic couplings for the Bridge Adapter Pallet (BAP). This is fitted to the M1977 Common Bridge Transporter (CBT) variant of the HEMTT.

The Multilift MPH (Military Pivoting Hooklift) range is based around commercially proven technologies, the overall system performance being improved by enhancing below ground pick up and the ability to load misaligned flatracks, both important military operational requirements. The complete system is designed to be used in all operational conditions, including darkness or while wearing nuclear, biological and chemical (NBC) protective equipment. An automatic, fully sequenced control system mounted in the cab aids operational safety and maximises speed, even under battle conditions. The MPH range was designed and optimised to load, transport and unload flatracks conforming to the NATO standard (STANAG 2413). Flatracks can be pre-loaded at base with any military payload ready for dispersal to the required location. Payloads such as MLRS rockets, light armoured vehicles and command/control shelters can also be transported by using purpose-built flatracks with the correct locking systems built in.

In U.S. Army service the M1120 can be equipped with several different styles of flatracks for the load handling system. The M1077 and M1077A1 General Purpose A-frame flatracks are sideless flatracks used to transport pallets of ammunition and other classes of supplies. M1077 flatracks are 6.058 m long, 2.438 m wide, and 1.5915 m high over the A-frame. On the ISO-compatible Palletized Flatrack (IPF) Type M1 there are two end walls, one incorporating the A-frame. Both walls can fold down inwardly for stacking when empty. The dimensions of the IPF are the same as for the M1077, apart from the end walls that have a height of 2.083 m. The M3/M3A1 Container Roll-in/Out Platform (CROP) is a flatrack that fits inside a 20 ft. ISO container. The Container Handling Unit (CHU) is an add-on kit that allows for the loading/unloading and transport of standard ISO containers without the need for an intermediate flatrack.

The SOFRAME RM 22 PLM load handling trailer which was originally selected as the M1076 trailer component of the US Armys PLS is compatible with, and used with, the M1120 HEMTT. The RM 22/M1076 is a three-axle dolly-type trailer. It uses a mainframe assembled using electric welding, with a secondary frame supporting the front axle on a turning table and the drawbar; a steering lock allows the steering to be fixed when required. Two axles are provided at the rear and braking is on all three axles. Flatracks can be on- and off-loaded from the trailer by the prime movers load handling system.

The M1977 HEMTT Common Bridge Transporter (CBT) is a further development of the M1120 LHS, and in common with the M1120 LHS was initially introduced as part of the HEMTT overhaul/rebuild program. It is used for loading, transporting, and unloading Ribbon Bridge components and bridge erection boats.

M1120 HEMTT Load Handling System 1

M1120 HEMTT Load Handling System 2

M1120 HEMTT Load Handling System 3

M1120 HEMTT Load Handling System 4

M1120 HEMTT Load Handling System 5

Complete article available at this page.

your advertise here

This post have 0 komentar


EmoticonEmoticon

Next article Next Post
Previous article Previous Post

Advertisement

Themeindie.com